Exhaust Type Tumble Dryer
T50DM
Please read this manual
carefully before using.
Retain it for future reference.
Important Safety Instructions
13.Do not allow children to play on, climb on or in the appliance. Close supervision
of children is necessary when the appliance is used near children.
14.Before the appliance is removed from service or discarded, remove the door to
the drying compartment.
15.Keep your dryer away from combustible materials (such as gasoline) during
operation to prevent the risk of fire.
16.Do not use or place stove, gas device, water heater, tinder or similarities close to
your dryer. Do not install or store this appliance where it will be exposed to water
and/or to the weather.
17.Do not tamper with controls.
18.Do not repair or replace any part of the appliance or attempt any servicing unless
specifically recommended in the user-maintenance instructions or in published
user-repair instructions that you understand and have skills to carry out.
19.Keep area around the exhaust opening and adjacent surrounding areas free from
the accumulation of lint, dust and dirt.
20.If material has been used with any flammable liquids or solids it should not be
used in the dryer until all traces of the flammable liquids and its fumes have
been removed.
21.This dryer shall be connected to a three-wire, single phase, 220-240V AC
power receptacle more than 10A, which must be reliably grounded. A leakage
protector shall be used, if possible.
22.Do not share a receptacle with other appliances. Do not use it when a plug
loosely inserted into a receptacle.
23.Do not excessively bend, stretch, twist, bind power cord or put heavy stuff on
it. Keep the terminator of power cord clean. Carefully clean it with dry cloth if
dusts accumulated. If damaged, power cord or plug must be replaced by our
service agent or qualified after-sale service person to avoid the risk of danger.
2
Important Safety Instructions
24.When normally using, the power cord of dryer shall be easily plugged or
unplugged by hand. It must be unplugged during power blackout, moving, not
in use or cleaning. Do not plug or unplug the power cord with wet hands.
25.Always disconnect dryer from electrical supply before attempting any service.
Disconnect power cord by grasping the plug, not the cord.
26.Do not block the exhaust vent when dryer operating to prevent it from
overheating or other dangers.
27.Do not let your dryer operate on packing foam. Otherwise it maybe cause fire
since heat accumulation or other external factors.
28.Only place sufficiently dehydrated clothes into your dryer for drying to prevent
leakage and longer drying time.
29.Do not place washed wet clothes in your dryer for a long time not drying them
(which may result in water leakage).
30.Don't touch the intake for the high temperature during the drying cycle.
31.Do not exceed dryer rated Max. Capacity.
32.The appliance must not be installed behind a lockable door, a sliding door
or a door with a hinge on the opposite side to that of the tumble dryer.
Names Of The Parts
Drum
Door
Exhaust Shroud
Window
Timer Selector Knob
Air Intake Shroud
Door Gasket
Heat Selector Knob
Power Cord
Casing
Exhaust Vent
Back Cover
Please check if the power receptacle has good earthing
Condition before using to guarantee your safety.
The manufacturer will not take responsibility for those
Risks occurred from not obeying this manual.
Operation Cautions
Avoid to dry starched clothes in
your dryer to prevent link filter
from clogging, which may lead
to bad exhaust performance.
Clothes with ribbon or lace
should be dried in a nylon net
Put chemical fiber and/or clothes
with ribbon or lace
into a nylon net
before drying.
Put rumpled clothes in order
Put all clothes in order after
dehydrated
before drying
them.
Clothes with zipper
Dry this kind of clothes with zipper
zipped or fastener
buckled and inside
out (to reduce the
impact noise between
metal and the drum)
Anti-wrinkle method for clothes
crumpled easily
Decrease capacity to get good anti-
wrinkle result (the capacity shall be
4/5 of that of normal clothes).
Do not load your dryer when
it is running.
Loading the dryer when it is running
shall be avoided to prevent the clothes
overdried or
Capacity reduced
incompletely
dried.
Remove the clothes out of your dryer
as early as possible
to reduce rumples.
Please flip clothes over manually
from time to time, if necessary,
when drying large ones.
It is not easy to flip over large clothes
(such as overcoat) in the drum, uneven
drying therefore happens sometimes.
If necessary, flip them over manually
from time to time to make them dried
Please hang the easily crumpled clothes
up with a hanger after dried
completely.
Flip over clothes
Installation Instructions
For your safety and correct using your dryer, please observe all the instructions
in this manual toinstall and adjust your dryer.
Location of your dryer
Dryer should be located in a dry and well-vented place, not filled with moisture and
vapors and where rain cannot reach (like bathroom,open balcony and water faucet).
Do not locate your dryer in a place where sunlight directly shines.
Do not use stove, gas etc. near your dryer to avoid dangers.
Locate your dryer on horizontal solid ground, floor or a
special bracket to prevent vibration and noise. Keep a dista
nce of 10cm-15cm away from the rear wall when installing.
The dryer has air intake and exhaust cycles,which
10-15cm
needs good air-exhaust vent in the rear and well-vented
room. If used in a small space, air exchange fan or
exhaust duct can be installed at the vent to exhaust
hot wet air outdoors.
The length of exhaust duct shall not exceed 2m.
Install and use the fixed legs of your dryer
Leg
If the dryer is not used with bracket, take fixed
legs out of the accessory bag and screw them
into the assembly hole of the dryer to ensure
it be placed stable.
Soft items
6
F
7
8
Using Method
1. Plug the power cord
The appliance shall be supplied with220- 240V,50Hz,
connected to a special receptacle more than
10A (reliably grounded).
2. Place the dehydrated clothes in your dryer
Check the following items before putting clothes in.
They shall be loaded in such a way that 2-3 pieces
each time and not in a group to avoid tangling, which
is not easy to turn it over resulting in uneven drying
since the clothes were wrapped.
Please put clothes into the drum. Avoid clothes being
pressed by the door due to exposure out of the port,
which will cause clothes entangle and door gasket
release and consequently poor drying effect.
Before drying your clothes
Make sure if clothes have any special requirements and suitable for drying.
Do not dry your clothes in your dryer if the materials of which cannot be dried
in a dryer or they bear the following labels:
Hang to dry
Do not tuumble dry
Drip dry
Dry flat
Dry in thhe shade
Carefully check the clothes to be dried and remove combustible
material such as lighter and match as well as sharp metal items
like coin, hair clip and safety pin maybe mixed with the clothes
and in pockets.
Clothes with zipper or fastener shall be put into your dryer inside
out with zipper zipped and fastener buckled.
Separate dark and light colored items, like you do for washing.
Check for stains that may not have been removed in washing.
Dryer heat may permanently set some stains. Properly dried clothes
will need minimum of care when removed from dryer.
For optimum results,use dryer load of similar fabric, weight and construction.
Placesmall items in a mesh bag prevent from tangling.Do not overload the dryer.
An average load will fill up half the drum.
9
Using Method
3. Control panel and its functions
Heat Selector Knob
Select drying level according to the material, quantity and drying
requirements of the clothes to be dried as shown in the figure
Select ' strong Dry' for clothes particularly thick and in large
quantities or in lower room temperature.
Soft
Select ' Soft Dry' for clothes not resistant to heat (like nylon,
chemical fibre and silk).
Strong
Heat Selector Knob
Drying Timer Knob
According to the selected dry time and heater working or not, five dry
combinations are available: cool, anti-wrinkle,warm,hot dry and air fluff
Air dry
Cool
OFF
Motor keeps running after dryer time
heating finished while heater stops
working and cold air into the drum to
cool laundry. The whole cooling will be
finished once the timer knob gets to
' OFF' position.
For down, sweater,
mohair, cotton sweater
and cotton-padded
clothes needing
freshening, tumbles
without heat. Also can
be individually used for
clothes long time in
closet with the
Power off when the
timer knob in
' OFF' position.
The dryer starts
when turn the knob
clockwise.
same results.
Anti-wrinkle
OFF
0
Air dry
40
60
Cool
Set ' Dry Timer' between 30
to 60 minutes based on
laundry quantity and set
20
OFF
40
' Heat selector knob' in '
Soft' position. After the
timer stops (including
Cooling program),the
laundry will still contain
some moisture which can
be ironed with an
electrical iron. This
program is mainly used for
laundry needs to be ironed.
Power off when the
timer knob in
' OFF' position.
The dryer starts
when turn the knob
clockwise.
20
60
0
OFF
80
220
200
100
120
Warm
Hot
180
140
160
Drying time(min)
Hot
Warm
For drying laundry in large quantity in
one time (more than 1/2 of the capacity
of drum) or particularly thicker clothes.
Timer set more than 150 minutes with
' Heat selector knob' in ' Strong dry'
position to dry the clothes throughly.
For normal laundry, timer set between 60 to
150 minutes and set ' heat selector knob' in
' Strong' or ' Soft' position as required.
After the dryer stops running, clothes
normallycan be dried ,cooled and anti-wrinkle.
10
Using Method
4. Set ' heat selector knob' to select ' Strong
dry' or ' Soft dry' level.
' Strong dry' level for large quantity and low room temperature.
Soft
Strong
' Soft dry' for non heat-resistant clothes.
Heat selector knob
5. Dry time settings
Select dry program according to clothes materials and
quantity, turn the timer knob to relative position. The
dryer starts running.
Do not point the
cursor to blank.
Please refer to page 10 ' Control panel and its functions'
and page 12 ' Dry Capacity Dry Time Reference Table' .
OFF
0
Air dry
40
60
Cool
20
40
20
Caution: Dry timing knob cursor
shouldn't be set at the blank area,
as indicated in the right figure.
Do not
60
0
OFF
point the
cursor to
blank
80
220
200
100
120
Warm
Hot
180
140
160
Drying time(min)
6. Do not take the laundry out until drying process is done
The last 20 minutes of hot air drying is cooling
to reduce the temperature of laundry inside
the drum.
To take the laundry out during drying, please
run cooling operation first since the temperature
inside the drum must be high.
Static electricity, due to friction, will be
generated on clothes made of chemical fibre
after dried. You can feel it when taking them out,
which is normal and shall not to be worried about.
7. Unplug the power cord
Please hold plug to unplug power cord from
a receptacle. Do not pull electrical wire directly
to prevent internal breakage or bad connection.
8. Clean filters
Clean the lint filter after every load and before each use. A clean filter ensures
sufficient drying. A layer of lint on the filter reduces airflow through the clothes
and prolongs drying time
Refer to the instructions on page 13.
DryCapacity DryTimeReferenceTable
Approx.5.0kg
Approx.1kg
Approx.2kg
Approx.3kg
Dry Capacity
Strong
Approx.50min
Approx.90min
Approx.90min
Approx.150min
Dry time
Approx.150min
Approx.220min
Soft
Dry time affected by many factors, such as material, weight, thickness and the hydrated
ratio of clothes , the above listed dry time is only for reference.
Care And Cleaning
Clean the buildup such as lints on filters in time after each use, otherwise it will affect
the performance of your dryer.
Please unplug the power cord first when cleaning it.
Cleaning of filters
The lint filter must be used for drying.
It must be cleaned in time befor and after each use.
The filter fixed in the
bottom of the drum
1. Remove the filters
Remove by pulling straight up with hands inserted
into the four holes around the exhaust vent shroud
in the sequence of ' Exhaust vent shroud - Lint filter -
Exhaust filter' , as shown in figure 1.
Lint
filter
Exhaust
Filter
Exhaust
vent shroud
2. Clean the lints
Figure 1
Separate
'
exhaust vent shroud
'
,
'
lint filter' and' exhaust
filter and clean the lints on the filter and exhaust filter
'
with a soft brush or vacuum cleaner.
Do not damage the filters (as shown in figure 2)
Lint Filter
Lints
Exhaust Filter
Dust Cleaner
3. Install the filters
Figure 2
After cleaning, assemble in the sequence of ' exhaust filter
-filter-exhaust vent shroud' ,align the recesses in the center
of filter with the projection in the center of drum and make
sure that it is firmly inserted (as shown in figure 3).
Note: The filter fixed in the bottom of the drum shall also
be cleaned with a soft brush.
Figure 3
DO NOT USE YOUR DRYER WITHOUT THE LINT FILTER.
Clean the interior drum or dryer
housing, with wet soft cloth, if stained.
Do not wash directly with water.
Do not use thinner, gasolene or alcohol.
Do not use any type of spray cleaner when
cleaning the interior. Hazardous fumes or electric
shock could occur. If dryer drum becomes stained,
clean the drum with a damp cloth. Remove any
residue before drying the next load.
Clean cabinet with mild soap and water. Donot use
harsh or abrasive cleaners, this could damage the
dryer.
Do not let any kind of liquid get into the air
intake or on the control panel.
Trouble Shooting
(If your dryer exhibits problems, please unplug the power cord before checking) The following
maybe unrelated to a malfunction of the dryer itself, please reconfirm before calling a
serviceman. If it does relate to a malfunction, please contact our service agent or after-sales
service and do not repair it by yourself.
Problem
Possible Cause
What to do
Insert the powercord firmly
Timer knob does not
turn
Is the power cord inserted
firmly?
Close the door.
Drum does not turn
Is the door closed?
Insert the power cord firmly.
Is the power cord inserted?
Does the receptacle have
power?
Check the power cord
receptacle.
No hot air blown out
Is the timer incorrectly
set up in cold air?
Set to hot air
Clean the filter.
The laundry is not
throughly dried (some
of the clothes still wet
after dryer stops)
Is the back filter
clogged?
Dehydrate the laundry
completely.
Have the clothes
been fully dehydrated?
Reduce the laundry quantity.
Dry the undried laundry again.
Is the laundry too much?
Have the dryer have been
added during operation?
Loose the twisted laundry and
dry again.
Does the laundry twist?
Dry the undried laundry again.
Have any clothes dry easily and
hardly been dried together?
Place the dryer in a well-vented
place.
Is the dryer placed in a small
and badly-vented space?
Try again after power recovered
Insert the power cord firmly
Dryer does not start
Is power failure?
Is the power cord inserted firmly?
Close the door
Set dry time
Is the door closed?
Is the timer in OFF position?
Specification
Model
T50DM
Rated Voltage Frequency
Rated Input Power
220-240V~ 50Hz
Extra 1070W
Light 700W
10A
Rated Fuse Current
Rated Max. Capacity
Overall Dimension
Net Weight
5.0kg
630mm 515mm 685mm
26.5kg
|